As I was filming new lessons for my CompactLogix course yesterday, I ran into an issue with version 15.01 of ControlFlash that I’m sure many other programmers have or will run into as well.
Note: If you’ve never used ControlFlash but need to, I’ve previously published step-by-step guides to flashing A-B Programmable Controllers over Ethernet (here) and USB (here.) I also have a guide on how to download Allen-Bradley Firmware here.
That said, you may find that when you download firmware files from Rockwell’s website that ControlFlash just seems to ignore them.
Why? Well, in today’s article I’ll cover three reasons this might happen.
First, you need to be sure you copy any downloaded Firmware files into the directories ControlFlash is set to use.
To see which directories your particular ControlFlash installation is monitoring, launch the software, then click on next, and then click on browse:
Second, you need to make sure the files you’ve downloaded have the “.dmk” extension. If your Firmware files have a “.zip” extension, you’ll need to rename them to “.dmk”.
Update for 2022: With ControlFlash 15.04, I’ve found you now need to open any zip files you download from Rockwell, and then run the .MSI install file inside.
In my case I downloaded every firmware available for my L73S, from v34 all the way back to v20. What I got was several .DMK files and several .Zip files in a subdirectory:
Just renaming the Zip files no longer worked for me, so I opened each one and ran the .MSI install file inside (after closing ControlFlash first:)
To do so, first check that you have File Explorer set to display “File Name Extensions” (that setting is found under the “View” tab, as shown below.) Then rename your downloaded Firmware file’s extension from “.zip” to “.dmk”:
![](https://i0.wp.com/theautomationblog.com/wp-content/uploads/2019/07/TheAutomationBlog-ControlFlash-NotFindingFW-04.png?resize=500%2C386&ssl=1)
Third, when you select the catalog number of your Controller, you may find that no matter what you do ControlFlash just won’t show any version higher than 30.011 (the workaround / solution is covered in the next paragraph):
The reason for this issue seems to be that versions after 30.011 are now “bundled” together under a family or controller line.
So in order to access those newer versions, you’ll want to scroll down below all the catalog numbers and then select the entire line or family like I do below:
I hope the above article helps those of you who ran into this issue like I did while filming my Compact Basics course.
If you have any questions or comments about this issue, you can post them in our free forum by clicking on the “post a comment or question” link below.
Until next time, Peace ✌️
Shawn M Tierney
Technology Enthusiast & Content Creator
Have a question? Join my community of automation professionals and take part in the discussion! You'll also find my PLC, HMI, and SCADA courses at TheAutomationSchool.com.
If you found this content helpful, consider buying me a coffee here.
- TAP Episode 200: Office Tour, Reflections, and Sincere Thanks! (P200) - April 24, 2024
- Automation Morning Show for April 23, 2024 (N179) - April 23, 2024
- Automation Morning Show for April 22, 2024 (N178) - April 22, 2024
Thank a lot!
You’re very welcome Tom!
Shawn
Join my free community to follow along! You can also become a member and support our work at: Automation.Locals.com
…versions after 30.011 are now “bundled”. That was what I need to read. Thanks for your help. I suppose it really does make sense from an organizational point of view.
You’re very welcome Scott – thank you for your comments,
Sincerely,
Shawn Tierney,
Instructor at http://www.TheAutomationSchool.com
Join my free community to follow along! You can also become a member and support our work at: Automation.Locals.com
Thank you!
The Versions after 30 being bundled made all the difference.
Thanks Ron – yeah that was a little tricky!
Sincerely,
Shawn Tierney,
Instructor at http://www.TheAutomationSchool.com
Once again…Shawn Tierney comes through with the answer! Thank you, sir!
Thanks @JP!
Sincerely,
Shawn Tierney,
Instructor at http://www.TheAutomationSchool.com
Thank you, I thought I was going crazy. I’ve been using Logix 5000 for over 20 years and it was not intuitive where the new firmware was, I never thought to scan past the L83E, L85E entries while looking for my L84E.
You’e very welcome @Timothy J McGuire,
Yeah, same thing happened to me, after which I figured I wasn’t alone 😉
Have a great weekend,
Sincerely,
Shawn Tierney,
Instructor at http://www.TheAutomationSchool.com
Exactly what I needed. Thanks!
Glad it helped @Kevin!
Shawn Tierney,
Instructor at http://www.TheAutomationSchool.com
Thanks for the help, I’ve spent 3hrs chasing my tail with downloading the firmware from Rockwell and trying to get it into the PLC. I’m no novice as used Rockwell and Siemens for decades but this new version was totally different. If it ain’t broke don’t fix it – Rockwell
Thanks @Graham, and I agree with you!!!
Shawn Tierney,
Instructor at http://www.TheAutomationSchool.com
I am experiencing the same thing, but the “controller families” are not showing in my controlFLASH. I am using controlFLASH v15.01 and Logix v30.01.
To be more specific, I need to add the CompactLogix 5370 (1769-L3) family to my inventory list to update the firmware on my 1769-L33ER controller.
Is it possible to add items to the inventory list?
Thanks for any help!
Yes – see my article on downloading firmware for ControlLogix and CompactLogix.
Shawn
Thank you
You’re very welcome 🙂
Shawn
I had to convert all my code to v24 version because i didn’t find the v31 firmware for a L33ER PLC. As someone said before, the Key was that v30 bundled all.
Thanks for post it!
You are very welcome! I know it’s frustrating how they changed it – maybe the will fix it in the future?
Shawn