CompactLogix, RSLinx Classic – How to Connect Using USB

In today’s article I walk you through how to configure RSLinx to communicate to a CompactLogix processor using USB.

Step 1) Locate your CompactLogix’s USB port

If you have one of Rockwell’s 5370 CompactLogix processors, you find an orange USB port on the front of the unit as shown below:

NOTE: If you have an older CompactLogix and would like to connect to its serial port using a USB to serial converter, see our previous article HERE.

Step 2) Plug a standard A to B USB Cable into the CompactLogix

Next, plug the B side of a standard A to B USB cable into the CompactLogix (this is the same type of cable used to connect a PC to a USB Printer):

Step 3) Insure your have RSLinx Classic version 3.51 or later installed

Before you plug the other end of your USB cable into your computer, insure RSLinx Classic 3.51 or later is installed on your computer.

Step 4) Wait for Windows to install the Rockwell USBCIP driver.

A few moments after plugging your USB cable into your PC you should see the below notices about the USBCIP driver being installed:

Step 5) Open RSLinx Classic to find USB driver automatically added

Once Windows adds the USBCIP hardware driver, open RSLinx Classic and you should find the USB software driver has been added automatically:

NOTE: If you use RSLogix Emulate 5000, SoftLogix 5800, or another USB product from Rockwell, you may have to manually delete those drivers from RSLinx (including the “Virtual Backplane” driver,) and restart RSLinx before you’ll see the USB driver appear in the RSWho window.

Step 6) Expand the USB Driver

Now expand the USB driver and then select it to allow RSLinx to begin to browse the USB port:

Step 7) Your CompactLogix show now be displayed under the USB driver

After a few moments, you should see your CompactLogix processor appear under the USB driver in the RSWho window. At this point you can use this USB connection to your CompactLogix to flash firmware, change the Ethernet address, download a program, and go online:

NOTE: Watch me run through the above steps in today’s episode of The Automation Minute!

• RSLinx to CompactLogix using USB (M2E12)

For more information:

If you’d like more information about connecting to your CompactLogix using USB, check out Rockwell’s excellent “Quick Start” guide below:

• CompactLogix 5370 L1 Controllers’ Quick Start

I hope the above article on how to setup RSLinx to communicate to a CompactLogix over USB was helpful.

If you have any questions or comments, please feel free to share them with us by clicking on the “post a comment or question” link below.

Until next time, Peace ✌️ 

If you enjoy this episode please give it a Like, and consider Sharing as this is the best way for us to find new guests to come on the show.

Shawn M Tierney
Technology Enthusiast & Content Creator

Eliminate commercials and gain access to my weekly full length hands-on, news, and Q&A sessions by becoming a member at The Automation Blog or on YouTube. You'll also find all of my affordable PLC, HMI, and SCADA courses at TheAutomationSchool.com.

• Author
• Recent Posts

Shawn Tierney

I'm a lifelong Technology Enthusiast who started programing in the early 80's on the new Apple II and VIC-20 personal computers. After earning a degree in Electronics, I worked as a Certified Automation Specialist for 25 years before leaving to focus on teaching at The Automation School, as well as publishing industry news and product how-to’s at The Automation Blog.

Latest posts by Shawn Tierney (see all)

• TAP228 Aftershow: Can Ai Really Explain, Write and Edit PLC Code? (PAS01) - November 22, 2024
• Automation Q & A for November 22, 2024 (QW023) - November 22, 2024
• SLC-500 Migrations Compared: SoftPLC vs Studio 5000 (S2E10) - November 21, 2024