As I was prepping to film additional lessons for my CompactLogix course yesterday, I ran into a completely new Studio 5000 Logix Designer “Fatal Error” that I hadn't run into before.
NOTE: For those who are having this issue and need to fix it asap, use this LINK to scroll down to the details about the fix I implemented.
In fact, over the last few months I've been spending a lot of time in RSLogix 5000 v20, and Studio 5000 Logix Designer v30, creating and refining the code and scenarios for my Compact Basics course's new programming lessons.
Not having run into any issues with either v20 or v30, you can probably imagine that I was a little frustrated during rehearsals for my “Studio 5000 First Look” lesson, when every time I tried to create a v21 project Studio 5000 crashed.
Off Topic: After submitting many and varied messages to Rockwell about how tech notes like these (you know, the ones with information you need to actually get the product you purchased to work) should not be locked, I've come to the conclusion either they don't read customer feedback, or they just don't agree with these sentiments.
Since I had purchased a support contract last summer to gain access to the latest software updates (albeit with delayed access to Studio 5000 updates as I don't own the most expensive editions,) I logged with my account in order to unlock them (links below:)
- RSLogix 5000/Studio 5000 : 0xc0000005 fatal error during startup (requires support contract to view)
- Studio 5000 / RSLogix 5000 : Fatal Error 0xc0000005 on Windows 8 / 8.1 / 10 (requires support contract to view)
To summarize what I learned, it appears that installing newer versions of Studio 5000 can break older versions, something software vendors have been struggling with since the introduction of the personal computer.
That said, after reading through the fixes detailed in those tech notes, I found that none of them were too appealing.
How to stop Studio 5000 Logix Designer from causing a Fatal Application Error:
Step 1: Navigate to the “Launcher” directory in your “Studio 5000” installation directory.
On my VM it was: C:\Program Files (x86)\Rockwell Software\Studio 5000\Launcher
Step 3: Here, set the Launcher to run “as an Administrator,” and then click on Ok:
Step 4: Now when you run Studio 5000, you'll see a “User Account Control” confirmation popup as shown below. I'll leave it up to you if you'd like to make changes to your UAC settings to disable this message:
Step 5: After you're done with Studio 5000, you'll probably notice this window asking if the issue has been resolved (I clicked on “Yes” which seemed to stop this message reappearing:)
Now while I've just run into this issue myself, I'm sure some of you ran into it months or even years ago.
That being the case, it's likely one of you have come up with a newer or better fix, and if you have we'd all love to hear it!
You can share it with us along with any thoughts, questions, or opinions you have by clicking on the “post a comment or question” link below.
Enjoy the benefits of membership! Patreon.com/automation
Check out my affordable courses: TheAutomationSchool.com
Ask me questions by clicking here to go to the comments link
Have an industrial automation news tip? Share it with us here
- Siemens S7-1500: First Time Wiring and Programming (S45) - August 13, 2020
- SITOP Power Supplies and Selectivity Modules (P57) - July 24, 2020
- WAGO PLC Starter Kit Unboxing and Setup (S44) - July 17, 2020
Click HERE to scroll down to view or leave comments
- Just ran into this issue again!
Must have been when I added v31 and v32 my launcher got reset?Had this problem in the past, but now it is showing up in a different scenario... In version 32, using the "Alarm Manager" any time I attempt to close it or delete any alarm tags / alarm definitions, I get this same dreaded fatal error. I have selected "run as admin" for all of my launchers still to no avail. Anyone else having this problem or know of a solution?Sorry , I haven't been using 32 much 🙁