In March of 2022, Rockwell Automation released Studio 5000 Logix Designer version Thirty-Four.
As I tend to do with each release, I recently downloaded the software, read the release notes, and set out to install...
Recently one of our readers submitted a question asking for help migrating from a legacy RockwellPLC (aka PLC-5 or SLC-500) to their new PAC lines (ControlLogix and CompactLogix.)
In his email he went on...
I’ll admit, I don’t always investigate every new feature that I read in a software’s release notes and many times I fail to utilize them for some time. Such is the case for tag extended...
The industrial automation market in the USA is heating up, and many companies are finding it hard to hire people with the knowledge needed to maintain and upgrade automated systems.
And it's times like these...
Logix Programming Instructions Every Tech Needs to Know Part II
Image by Brandon Cooper
In part one of this series, we looked at an introduction to learning Studio 5000 programming instructions for ControlLogix processors as well...
Logix Programming Instructions Every Tech Needs to Know, Part I
Image by Brandon Cooper
Learning to program anything takes time and effort. The more investment that you make, the greater the return.
When I have set out...
Programmers can accomplish a task in many ways. They have many options available, and it is almost to the point that you can use whatever coding style your preference is for a task at...
Learn how to connect and use an Encoder with a CompactLogix and High Speed Counter module in this episode of The Automation Show.
For more information, check out the "Show Notes" located below the video.
The...
On September 30, 2020, Rockwell Automation released Studio 5000 Logix Designer version thirty-three.
As I tend to do with each incoming version, I downloaded the “Release Notes” and Software to check it out.
Image by: Brandon...
In this episode of The Automation Show I share my top picks from Rockwell's ROKLive Logix and View Presentations:
For more information, check out the "Show Notes" located below the video.
The Automation Show, Episode 42...
In this article I'll introduce you to the basics of a ControlLogix Function Block Routine Totalizer Instruction.
If you have ever used any Allen-Bradley software, you are familiar with their ladder logic programming. In many of...
In a previous article regarding ControlLogix processor faults, I mentioned one of the ways a processor can be faulted was by causing an array to go out of bounds when using an FFL and...
If the need arises to use specific time in your ladder logic program, this guide will give you a reference to go by.
Possibly you have a cleaning device that only needs to operate once...
When I think about controller redundancy, the first thought that crosses my mind is
“I better do my research, because the components have to be exact.”
If you are familiar with the redundancy setup, you know...
I first began using ControlLogix in 2001, back when the software and firmware were both at version 7.
In those early days it wasn't so easy to add a new remote I/O Chassis to an...
In modern industry, when it comes to production downtime, very few events are overlooked without an explanation.
“Failure analysis” on failed components, and “root cause analysis” for downtime events, are common terminology you will hear...
In this week's episode of The Automation Show, I cover how to use the MSG (Message) Instruction in the ControlLogix to read data from CompactLogix, SLC-500, and MicroLogix over Ethernet:
For more information, check out...
One of the gratifying opportunities in the life of a control system’s engineer is to successfully upgrade a legacy system to a newer system with more features and capabilities.
We, as automation specialists in general,...
In this week's episode of The Automation Show, I cover how you can use the MSG (Message) Instruction in the ControlLogix to read data from the PLC-5 and SLC-500 over a Data Highway Plus...
In this week's episode of The Automation Show, I cover how you can use the MSG (Message) Instruction in the ControlLogix to read data from CompactLogix, MicroLogix, and SLC-500 over a DH-485 network:
For more...