CompactLogix

What’s New With Rockwell’s Logix and View (P191)

This week I take a look at what's new with Rockwell's Logix and View products as seen at Automation Fair 2023 in this episode of The Automation Podcast. For more information, check out the "Show Notes" located below the video. Watch to the Podcast on The Automation Blog: [youtube https://www.youtube.com/watch?v=t5e-OwgpQYM?si=cIwH_l0qjTupvUyC] Listen to the...

CompactLogix – Why Does Its IP Address Keep Changing? (qa230221)

Automation Q & A from the Morning Show dated 02/21/23: A reader recently asked why does his CompactLogix's IP Address keep  reverting back to the old value every time he cycles power, and I share my thoughts on that in today's Automation Q&A. NOTE: You'll find the articles mentioned in this...

RSLinx – What To Do When The Ethernet/IP Driver Won’t Find Your Device (T006)

In this edition of Automation Tech Tips, I walk through how to setup the Ethernet Devices Driver in RSLinx Classic, which can be helpful if your device is not showing up in the Ethernet/IP driver. NOTE: If you need to learn how to use the CompactLogix, check out my CompactLogix...

BOOTP-DHCP Utility – Why Won’t It Disable BOOTP? (qa230210)

Automation Q & A from the Morning Show dated 02/10/23: I was recently asked by a community member what to do if the BOOTP-DHCP Tool/Utility wouldn't disable the BOOTP setting in a PLC and HMI, and I share my thoughts on that question in today's Automation Q&A below. NOTE: For our...

Message (MSG) – ControlLogix to PowerFlex 525? (qa230208)

Automation Q & A from the Morning Show dated 02/08/23: Recently I was asked by a community member if they could use a MSG instructions in a ControlLogix to communicate with a PowerFlex 525, and I share my thoughts on that question in today's Automation Q&A below: NOTE: If you need...

Studio 5000 – V35: What’s New

Late last year Rockwell released version 35 of Studio 5000 Logix Designer, and in today's article I'll cover the highlights of what's new and updated in the latest release. New Features: Axis Test Mode: Feature simulates real-time motion control behavior at the axis, module, or group level, without requiring connected...

Studio 5000 – V35: What’s New (P122)

Kristen Kosatka of Rockwell Automation comes on the show this week to share what's new with Studio 5000 v35 in Episode 122 of The Automation Podcast. For more information, check out the "Show Notes" located below the video. Watch the Podcast: [vimeo 757701813 w=750 h=420] The Automation Podcast is also available on most...

Three Questions Answered: Studio 5000, PanelView 800, CompactLogix (M5E37)

I answer three reader's questions on Studio 5000, the PanelView 800, and CompactLogix in Episode 37 of The Automation Minute, Season 5. [vimeo 741145429 w=750 h=420] The Automation Minute, Season 5 Episode 37 Show Notes: Episode Links: - Pickup our TAB1 Collection at TheAutomationBlog.com/tab1 Join our new community at Automation.Locals.com! Become part of our community...

ControlLogix, Studio 5000 – Rockwell Automation Update (P114)

This week Dennis Wylie and Justin Wengatz from Rockwell Automation bring us up to speed on What's New and Coming for ControlLogix and Studio 5000 on Episode 114 of The Automation Podcast. For more information, check out the "Show Notes" located below the video. Watch the Podcast: [vimeo 734713871 w=750 h=420] The Automation...

MQTT – Connect A-B PLCs & PACs to the Cloud (S2E01)

Learn how to connect A-B PLCs to the Cloud using an MQTT Gateway today on The Automation Show (S2E01) For more information, check out the "Show Notes" located below the video. [vimeo 650808618 w=750 h=420] The Automation Show, Season 2 Episode 1 Show Notes: Special thanks to RTA for sending in a sample...

FactoryTalk Logix Echo from Rockwell (P85)

My guest this week is Brad Prosak of Rockwell who introduces us to FactoryTalk Logix Echo in Episode 85 of The Automation Podcast. For more information, check out the "Show Notes" located below the video. Watch the Podcast: [vimeo 646571151 w=750 h=420] The Automation Podcast is also available on most Video and Podcasting...

Migrate / Convert – PLC-5, SLC-500, and MicroLogix Programs to RSLogix/Studio 5000 and Logix Controllers

Recently one of our readers submitted a question asking for help migrating from a legacy Rockwell PLC (aka PLC-5 or SLC-500) to their new PAC lines (ControlLogix and CompactLogix.) In his email he went on to say he needed help because he didn't have a copy of the Project Migrator,...

TIA Portal, S7 – Read and Write to ControlLogix Tags from a Siemens PLC

I would think that it would be extremely nice to have an entire manufacturing environment using the exact same control system with the same hardware and software throughout, but I can imagine that there are very few, if any, systems that are this seamless. When multiple control systems are working...

GuardLogix – Writing Logic in your Safety PLC

In a previous article, we discussed some safety options from Rockwell for a safety PLC as well as industry standards such as IEC 61508 and SIL ratings. In this article, I want to venture into the software side and take a look at a couple of the safety instructions you...

GuardLogix – Getting Started

For a machine application that involves a safety system, guarding or other needed safety equipment, Rockwell, as well as other vendors, provide safety solutions that meet the requirements to replace safety relays and hard-wired safety controls up to SIL 3 applications. In this article, I will hopefully explain what some...

CompactLogix – 5380: Why Are My 5069-IF8 Analog Inputs Updating Slowly? (Q&A)

One of our community members recently asked what would cause his 5380 analog inputs updating so slow? His application required that each 5380 analog inputs updated every 10ms, but what he was seeing in the field was a much slower. When working with analog inputs and Logix PACs, two settings will...

Logix Instructions – Bit Field Distribute and Message (MSG)

Logix Programming Instructions Every Tech Needs to Know Part II Image by Brandon Cooper In part one of this series, we looked at an introduction to learning Studio 5000 programming instructions for ControlLogix processors as well as an application for using the CPT and ABS instructions. I want to continue further and...

Logix Instructions – Compute and Absolute

Logix Programming Instructions Every Tech Needs to Know, Part I Image by Brandon Cooper Learning to program anything takes time and effort. The more investment that you make, the greater the return. When I have set out to embark on learning a new system, I first browse through other people’s code in...

ControlLogix – Programming: Different Ways of Accomplishing Your Goals

Programmers can accomplish a task in many ways. They have many options available, and it is almost to the point that you can use whatever coding style your preference is for a task at hand. PLC code does not need to be fancy, but it does help to be efficient,...

IFM – IOLink Master: How To Setup with Logix

In this article I'll walk you through how to set up the communications of an IO-Link master with an Allen Bradley CompactLogix PLC. The first thing that needs to be done is to setup up a free account at IFM.com. This is required to download the IFM software used to...